How to Jailbreak Your iPhone 4 iOS 6.1.3 Redsn0w

First of all you need to know that this is Tethered Jailbreak; now what does this mean? Whenever you reboot your device you will have to connect it to your PC and re-run Redsn0w. I hope it is now clear to you! Now lets talk Jailbreak iPhone 4 running iOS 6.1.3 using Redsn0w. As there are still no unthethered Jailbreak available for iOS 6.1.3, then thether Jailbreak is the only available option to jailbreak your iPhone.

Guidelines and Requirements:

  • This is Tethered Jailbreak
  • Your device should be running iOS 6.1.3 ( if not then download iOS 6.1.3 and Update it through iTunes)
  • Download iOS 6.0 between iOS 6.1.2 from here
  • Make sure you Backup of your iPhone in iTunes.

Jailbreak iPhone 4 on iOS 6.1.3

The following are the instructions to tethered jailbreak your iPhone 4 running on iOS 6.1.3.

STEP 1: First Download Redsn0w.

STEP 2: Make sure you have downloaded iOS 6.0 or iOS 6.1.2

STEP 3: Now extract the zip file on your desktop. And Launch Redsn0w

Redsn0w: Click on Extras to start Jailbreak iPhone 4STEP 4: Now to start jailbreak process click on Extras Button

Redsn0w-iPhone-4-Tethered-Jailbreak-4STEP 5: Then hit the Select IPSW Button

Redsn0w: Select IPSWSTEP 6: Now select iOS 6.0 IPSW file, which you must have downloaded before!

STEP 7: Redsn0w shall give a confirmation message that this will be used through out this jailbreak session. Just hit OK.

Redsn0w: The following Build was identifiedSTEP 8: Now click on Back Button and then hit the Jailbreak Button.

Redsn0w: Jailbreak iPhone 4STEP 9: Through this step Redsn0w will start preparing Jailbreak Data for your iPhone 4.

Redsn0w: Preparing Jailbreak DataSTEP 10: Now from the options check “Install Cydia” and click Next to Proceed

Redsn0w: Check install Cydia OptionSTEP 11: Here you are then asked to Switch Off your iPhone completely.After your device is off click on Next Button.

Redsn0w: Switch off your device to proceed jailbreakSTEP 12: After step 11 Redsn0w will guide you how to enter your device into DFU Mode.

Redsn0w: Hold the Power button for 3 secs

Redsn0w: Without releasing the power button hold the Home button for 10 Seconds

Redsn0w: Now release the Power button but keep holding the Home Button for 15 SecondsIf you are confuse how to DFU Mode Learn Here

STEP 13: After DFU Mode Redsn0w will show you a message saying, “Exploiting with limera1n”

Redsn0w: Exploiting with Limera1nSTEP 14: Redsn0w will now reboot your iPhone 4.

Redsn0w: Waiting for Reboot

STEP 15: Redsn0w will now upload Ramdisk to your device.

Redsn0w: Uploading Ramdisk

STEP 16: As the ramdisk uploading completes, Redsn0w will then confirms that you have successfully tethered jailbreak your iPhone 4.

Redsn0w: iPhone 4 tethered Jailbreak successfulSTEP 17: Now what you need to do is click on Back Button and headover to Extras

Redsn0w-iPhone-4-Tethered-Jailbreak-15STEP 18: And click on Just Boot

Redsn0w: Select IPSWCongratulations! You’ve now successfully tethered jailbreak your iPhone 4 running the iOS 6.1.3. Do not forget to share your experience in the comment section below. For more Jailbreak guides and iOS tips keep visiting.